ENVS1 range · transducers · footprint · cabling

ENVS1 transducers and footprintUltrasonic antifouling transducers

Hermetically potted, IP68 beyond 10 m, bonded via the proprietary footprint.

ENVS1 transducers are the ultrasonic antifouling transducers ENVSonic has designed and built in Australia since 2006: proprietary primary and secondary mass materials matched to the drive, a treated PVC shell and industrial silicone-rubber tinned-copper cable. Each unit is analysed, then hermetically sealed by degassed potting to IP68 beyond 10 m, ready for a dry box-cooler install or a flooded ballast tank, for life. The proprietary footprint makes the transducer monolithic with the structure and puts up to 30% more energy into it than grease or isolated-face mounts. Watch the ENVS1.T50 / T60 installation video.

IP68
Beyond 10 m
+30%
Energy transfer via footprint
Daily
Self-calibration
Transducer
Hardware

Footprint and mounting

Proprietary footprint
Proprietary footprint mount
Models

Transducer models

Transducer on rudder
ENVS1.T50 Current
Transducer on rudder
ENVS1.T60 Current
ENVS1.T100 Coming
ENVS1.T100-WEKA Coming
Model Status For Note
ENVS1.T50 Current Hulls, sea chests, box coolers, strainers, running gear Install video on /install/t50/
ENVS1.T60 Current Larger structures and longer runs
ENVS1.T100 Coming Higher output for large plate areas Specifications on release
ENVS1.T100-WEKA Coming Factory-integrated protection for WEKA Marine box coolers Developed with WEKA Marine for box-cooler integration; specifications on release
Built for

Every ENVSonic installation

Box coolers and sea chests Bonded through the footprint to the dry side of the sea chest or cooler casing, inside the vessel. Nothing outside the hull, no drilling of the pressure vessel, no docking.
Hull plating Internal bonding to plating; ballast-tank cable penetrations require class approval.
Running gear Mounted on structure adjacent to shafts, rudder stocks and thruster tunnels; nothing in the water flow.
Pipework and plant Raw-water pipe, heat exchangers, cooling towers and intakes.
Installation

Transducer and footprint

12345
  1. Epoxy bond: fixes the footprint to the inboard side of the steel. A watertight seal with electrical isolation.
  2. Footprint: shaped to the surface it sits on, flat for plate or matched to the outside diameter of a pipe.
  3. Gasket sealant: a thin layer on the face of the transducer, between it and the footprint.
  4. Transducer: hermetically potted to IP68, it threads onto the footprint.
  5. Together they act as one piece with the structure, with up to 30% more ultrasonic transference.
Features

What's in the box

01
Hermetically potted

Degassed potting seals every unit; IP68 beyond 10 m, dry or flooded.

02
Proprietary mass

Primary and secondary mass materials matched to the drive.

03
Treated PVC shell

Marine-grade shell for the life of the vessel.

04
Industrial cable

Silicone-rubber, tinned-copper cable rated for engine rooms and tanks.

05
Proprietary footprint

Watertight seal and electrical isolation, monolithic with the structure.

06
Up to 30% more transference

Against grease or isolated-face mounting; no silicone grease to break down.

07
No plastic threads

Nothing coarse to loosen; inspection requirements cut.

08
Calibrated daily

Each transducer profiled to its installed environment by the control module.

Specifications

ENVS1 transducers and footprint at a glance

Models ENVS1.T50 · ENVS1.T60 · ENVS1.T100 (coming) · ENVS1.T100-WEKA (coming)
Ingress protection IP68 beyond 10 m, hermetically potted
Construction Proprietary primary and secondary mass, treated PVC shell
Piezoceramic PZT; its lead is sealed inside the potting and permitted under the EU RoHS exemption for lead in piezoelectric ceramics
Power 60 W rated, driven in full on every burst; typically 6 to 8 W average, set by the duty cycle
Cable Industrial silicone-rubber, tinned copper
Mount Proprietary footprint: watertight seal, electrical isolation, up to 30% more ultrasonic transference
Dimensions and weight To be confirmed
Calibration Daily, per transducer, by the control module
Installation Bonded through the footprint to the inboard side of the hull plating or structure, inside the vessel. Nothing is fitted outside the hull: no drilling, no welding, no through-hull penetrations, and no docking for most installs
In service

Where it's working

Scope ENVS1 transducers and footprint for your fleet

Protects: box coolers, sea chests, strainers, pipework, hull plating, props, shafts, rudders, thrusters, cooling towers and intakes. Send the GA and we'll return a transducer plan and proposal.

Request a proposal